product bulletin see capacitance value chart below for thickness dimension. + for extended values 1210 case sizes - solder reflow only. (refer to f3102 catalog for additional soldering information and re commendations.) outline drawing
surface mount ceramic chip capacitors ? ultra-high capacitance, c0g dielectric ? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com f9200 11/07 eia size code metric size code l - length w - width b - bandwidth s separation minimum mounting technique 0402 1005 1.0 (.04) .05 (.002) 0.5 (.02) .05 (.002) 0.20 (.008) -.40 (.016) 0.3 (.012) solder reflow 0603 1608 1.6 (.063) .15 (.006) 0.8 (.032) .15 (.006) 0.35 (.014) .15 (.006) 0.7 (.028) solder wave + or solder reflow 0805 2012 2.0 (.079) .20 (.008) 1.25 (.049) .20 (.008) 0.50 (.02) .25 (.010) 0.75 (.030) 1206 3216 3.2 (.126) .20 (.008) 1.6 (.063) .20 (.008) 0.50 (.02) .25 (.010) n/a 1210 3225 3.2 (.126) .20 (.008) 2.5 (.098) .20 (.008) 0.50 (.02) .25 (.010) n/a dimensions - millimeters (inches) c 0805 c 103 k 5 g a c style c - ceramic size code 0402, 0603, 0805, 1206, 1210 specification c - standard capacitance code, pf first two digits represent significant figures. third digit specifies number of zeros. 100 pf = 101. (use ?9? for 1.0 through 9.9 pf) (use ?8? for 0.1 through .99 pf) capacitance tolerance f = 1% k = 10% g = 2% m = 20% j = 5% voltage 8 = 10v 5 = 50v 4 = 16v 1 = 100v 3 = 25v temperature characteristic designated by capacitance change over temperature range g = c0g (np0) (30 ppm/c) end metallization c = standard (tin-plate nickel barrier) failure rate level a = not applicable ordering information
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com as detailed in the kemet surface mount catalog f3102 for c0g, with following specific requirements based on room temperature (25c) parameters: ? operating range: -55c to +125c, with no-bias capacitance shift limited to 30 ppm/c over that range. ? insulation resistance (ir) measured after 2 minutes at rated voltage @ 25c: limit is 1000 megohm microfarads or 100g , whichever is less. ? capacitance and dissipation factor (df) measured at the following conditions. capacitance - 1 khz and 1 vrms if capacitance >1000 pf 1 mhz and 1 vrms if capacitance 1000 pf df limit is 0.1%. components are suitable for wave and ir reflow soldering except extended 1210 values which are suitable for ir reflow only. all parts incorporate the standard kemet barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching. (please refer to kemet catalog f3102 for additional soldering information and recommendations.) these chips will be supplied unmarked. however, marking is available as an extra cost option. aec-q200 rev. c - automotive rohs 6/6 - 100% tin termination electrical parameters soldering process marking qualification/certification in general, the information in the kemet surface mount catalog f3102 applies to these capacitors. the information in this bulletin supplements that in the catalog.
capacitance value (pf) kemet part number voltage capacitance tolerance thickness - mm (inches) qty 7" reel qty 13" reel 1100 c0402c112_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 50,000 50,000 1200 c0402c122_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1300 c0402c132_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1500 c0402c152_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1600 c0402c162_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1800 c0402c182_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2000 c0402c202_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2200 c0402c222_8gac 10 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1100 c0402c112_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1200 c0402c122_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1300 c0402c132_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1500 c0402c152_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1600 c0402c162_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1800 c0402c182_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2000 c0402c202_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2200 c0402c222_4gac 16 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1100 c0402c112_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1200 c0402c122_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1300 c0402c132_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1500 c0402c152_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1600 c0402c162_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1800 c0402c182_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2000 c0402c202_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 2200 c0402c222_3gac 25 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 360 c0402c361_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 390 c0402c391_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 430 c0402c431_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 470 c0402c471_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 510 c0402c511_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 560 c0402c561_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 620 c0402c621_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 680 c0402c681_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 750 c0402c751_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 820 c0402c821_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 910 c0402c911_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1000 c0402c102_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1100 c0402c112_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1200 c0402c122_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1300 c0402c132_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1500 c0402c152_5gac 50 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 100 c0402c101_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 110 c0402c111_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 120 c0402c121_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 130 c0402c131_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 150 c0402c151_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 160 c0402c161_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 180 c0402c181_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 200 c0402c201_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 220 c0402c221_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 240 c0402c241_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 270 c0402c271_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 300 c0402c301_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 330 c0402c331_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 360 c0402c361_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 390 c0402c391_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 430 c0402c431_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 470 c0402c471_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 510 c0402c511_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 560 c0402c561_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 620 c0402c621_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 680 c0402c681_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 750 c0402c751_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 820 c0402c821_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 910 c0402c911_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 1000 c0402c102_1gac 100 f, g, j, k, m 0.50 (0.02) 0.05 (0.002) 10,000 50,000 ratings & part number table - 0402 case size ? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com ratings & part number table - 0603 case size capacitance value (pf) kemet part number voltage capacitance tolerance thickness - mm (inches) qty 7" reel qty 13" reel 12000 c0603c123_8gac 10 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 15000 c0603c153_8gac 10 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 12000 c0603c123_4gac 16 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 15000 c0603c153_4gac 16 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 12000 c0603c123_3gac 25 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 15000 c0603c153_3gac 25 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2200 c0603c222_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2400 c0603c242_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2700 c0603c272_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3000 c0603c302_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3300 c0603c332_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3600 c0603c362_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3900 c0603c392_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 4300 c0603c432_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 4700 c0603c472_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 5100 c0603c512_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 5600 c0603c562_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 6200 c0603c622_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 6800 c0603c682_5gac 50 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 360 c0603c361_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 390 c0603c391_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 430 c0603c431_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 470 c0603c471_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 510 c0603c511_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 560 c0603c561_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 620 c0603c621_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 680 c0603c681_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 750 c0603c751_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 820 c0603c821_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 910 c0603c911_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1000 c0603c102_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1100 c0603c112_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1200 c0603c122_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1300 c0603c132_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1500 c0603c152_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1600 c0603c162_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 1800 c0603c182_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2000 c0603c202_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2200 c0603c222_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2400 c0603c242_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 2700 c0603c272_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3000 c0603c302_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3300 c0603c332_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3600 c0603c362_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 3900 c0603c392_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 4300 c0603c432_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000 4700 c0603c472_1gac 100 f, g, j, k, m 0.80 (0.031) 0.07 (0.003) 4,000 10,000
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com ratings & part number table - 0805 case size capacitance value (pf) kemet part number voltage capacitance tolerance thickness - mm (inches) qty 7" reel qty 13" reel 47000 c0805c473_8gac 10 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000 47000 c0805c473_4gac 16 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000 47000 c0805c473_3gac 25 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000 6800 c0805c682_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 7500 c0805c752_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 8200 c0805c822_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 9100 c0805c912_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 10000 c0805c103_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 12000 c0805c123_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 15000 c0805c153_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 18000 c0805c183_5gac 50 f, g, j, k, m 0.90 (0.035) 0.10 (0.004) 4,000 10,000 22000 c0805c223_5gac 50 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 2200 c0805c222_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 2400 c0805c242_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 2700 c0805c272_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 3000 c0805c302_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 3300 c0805c332_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 3600 c0805c362_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 3900 c0805c392_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 4300 c0805c432_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 4700 c0805c472_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 5100 c0805c512_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 5600 c0805c562_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 6200 c0805c622_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 6800 c0805c682_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 7500 c0805c752_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 8200 c0805c822_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 9100 c0805c912_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 10000 c0805c103_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 12000 c0805c123_1gac 100 f, g, j, k, m 1.00 (0.039) 0.10 (0.004) 2,500 10,000 15000 c0805c153_1gac 100 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000
? kemet electronics corporation ? p.o. box 5928 ? greenville, sc 29606 (864) 963-6300 ? www.kemet.com ratings & part number table - 1206 case size capacitance value (pf) kemet part number voltage capacitance tolerance thickness - mm (inches) qty 7" reel qty 13" reel 15000 c1206c153_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 18000 c1206c183_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 22000 c1206c223_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 27000 c1206c273_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 33000 c1206c333_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 47000 c1206c473_5gac 50 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 56000 c1206c563_5gac 50 f, g, j, k, m 1.20 (0.047) 0.15 (0.006) 2,500 10,000 68000 c1206c683_5gac 50 f, g, j, k, m 1.60 (0.063) 0.20 (0.008) 2,000 8,000 82000 c1206c823_5gac 50 f, g, j, k, m 1.60 (0.063) 0.20 (0.008) 2,000 8,000 6800 c1206c682_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 7500 c1206c752_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 8200 c1206c822_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 9100 c1206c912_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 10000 c1206c103_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 12000 c1206c123_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 15000 c1206c153_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 18000 c1206c183_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 22000 c1206c223_1gac 100 f, g, j, k, m 0.90 (0.035) 0.10 (0.004) 4,000 10,000 27000 c1206c273_1gac 100 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 33000 c1206c333_1gac 100 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 47000 c1206c473_1gac 100 f, g, j, k, m 1.60 (0.063) 0.20 (0.008) 2,000 8,000 ratings & part number table - 1210 case size capacitance value (pf) kemet part number voltage capacitance tolerance thickness - mm (inches) qty 7" reel qty 13" reel 18000 c1210c183_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 22000 c1210c223_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 27000 c1210c273_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 33000 c1210c333_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 47000 c1210c473_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 56000 c1210c563_5gac 50 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 68000 c1210c683_5gac 50 f, g, j, k, m 0.90 (0.035) 0.10 (0.004) 4,000 10,000 82000 c1210c823_5gac 50 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 100000 c1210c104_5gac 50 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000 120000 c1210c124_5gac 50 f, g, j, k, m 1.55 (0.061) 0.15 (0.006) 2,000 8,000 150000 c1210c154_5gac 50 f, g, j, k, m 1.70 (0.067) 0.20 (0.008) 2,000 8,000 12000 c1210c123_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 15000 c1210c153_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 18000 c1210c183_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 22000 c1210c223_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 27000 c1210c273_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 33000 c1210c333_1gac 100 f, g, j, k, m 0.78 (0.031) 0.10 (0.004) 4,000 10,000 47000 c1210c473_1gac 100 f, g, j, k, m 1.00 (0.039) 0.10 (0.004) 2,500 10,000 56000 c1210c563_1gac 100 f, g, j, k, m 1.10 (0.043) 0.10 (0.004) 2,500 10,000 68000 c1210c683_1gac 100 f, g, j, k, m 1.25 (0.049) 0.15 (0.006) 2,500 10,000 82000 c1210c823_1gac 100 f, g, j, k, m 1.55 (0.061) 0.15 (0.006) 2,000 8,000 100000 c1210c104_1gac 100 f, g, j, k, m 1.70 (0.067) 0.20 (0.008) 2,000 8,000
|
